Factory Camper AFT CURTAIN with clear Eisenglass windows zips to back of OEM Camper Top and Side Curtains (not included) and connects to Transom, OEM (Original Equipment Manufacturer) in Sunbrella® marine fabric, produced with the same high quality, original 2003-2003 digitized patterns approved by Sea Ray® for the 240 SDA Sundancer: 240SDA Sundancer with factory installed Radar-Arch (NOT the 2003 240DA):
Notes:
2003-2003 Sea Ray® 240 SDA Sundancer Model Specific Details: The Cockpit Cover goes OVER the windshield and snaps at the base of the windshield in front. Sea Rays with 12-digit Hull Identification Number (HIN) beginning with SERA were made in Arizona for which we do NOT have OEM canvas patterns (this boat was built by Sea Ray in AZ and TN): our Tennessee Sea Ray® Bow Covers, Cockpit Covers and Carpet Runners we offer will fit Arizona boats, however the original Arizona top frame(s) were made by someone else, so our Tennessee Bimini, Sunshade and Camper replacement canvas will NOT fit Arizona frames, AND our Visor, Side or Aft Curtains will NOT zip properly to original Arizona top canvas, BUT ALL Arizona canvas AND frames can typically be replaced as a set, however we do NOT guarantee fit. Sea Ray® originally offered the 2003-2003 240 SDA Sundancer in Black, Mediterranean Blue Tweed, Hunter Green Tweed and Toast Tweed (2002-2003) Sunbrella® (the Tops were originally SeaMark® vinyl-lined Sunbrella®, but are now Sunbrella® to avoid mold issues) fabric.
Product Details: Camper Top is an enclosure attached to the back of a Bimini, Sunshade, Convertible Top or Arch that has its own frame to cover to the back of the boat. Includes mounting hardware and Stainless Steel Snaps. When combined with Side-Curtains, the Camper-Top-Aft-Curtains fully enclose the back of the boat providing full, protected use of the rear cockpit area at the dock or underway. Snaps NOT installed in canvas, Snap Tool required. The Aft-Curtain has 25 to 60 standard 3/8" snaps or bungee cords, depending on the boat. Factory Original-Equipment (OEM) canvas made-to-order. The boat manufacturer and RNR-Marine™ do not recommend operating the boat with the aft-curtain in place, due to dangerous fuel and exhaust fumes. Also called: Boston Whaler "Sun-Top" or Grady White "Vista Top".
Sea Ray® Factory Original Equipment Manufacturer (OEM) Notes: Zippers on Sea Ray® canvas are size #8 (6 teeth/inch) up to 35 foot, #10 over 35 foot (5 teeth/inch). Cockpit Covers for open bridge boats (Sundancer, SunDeck, SunSport, SLX, Bowrider, Express Cruiser, Weekender) prior to 2008 cover the windshield, 2008 and newer attach to Top of windshield. Embroidered Sea Ray® logo on SOME (when offered by Sea Ray) Boot Covers was Tan (gold) until 2011, then Silver 2012 and newer. Sea Ray® installed the snaps in their boats, canvas and covers at their factory, so we cannot install the canvas snaps for you because we do not have locations (see Canvas/Snap Installation to learn about installing snaps). We can only sell canvas and covers direct for Sea Ray® boats over 2 years old. Sea Ray® OEM canvas/covers part numbers: [yySRmmm mm tar-xxxxx-fcc] where [yy] is the model year, [SR] is Sea Ray®, [mmm mm] is the boat model, [t] is the type of window or drive (S=Std-Windshield, W=optional-stainless-Windshield, I=I/O-sterndrive, O=Outboard), [a] is (A)rch or (N)o-arch, [r] is the revision, [xxxxx] identifies which canvas piece, [f] is the fabric (A=Sunbrella® acrylic, S=SeaMark®) and [cc] is the color code. Sea Ray® Hull Identification Number (HIN) = SERpssssmbyy , where [p] = mfg plant, [yy] = model-year.
Factory Original-Equipment-Manufacturer (OEM) patterned for the 2003 Sea Ray® 240 SDA Sundancer: 240SDA Sundancer with factory installed Radar-Arch (NOT the 2003 240DA).
Will ONLY fit and/or zip to other Factory OEM canvas/frames with GLBT tags p/n [03SR240SDA SAr -x0xxx-fcc], Sea Ray® p/n [1xxxxxx] ("cc" is the color code).
ONLY zips to Factory OEM Camper Top and Side Curtains (no tincluded).
Verify that your old and mating canvas has GLBT on the tags and embossed on the Canvas Snaps AND factory #8 zippers (6 teeth/inch), NOT #10 (5 teeth/inch) which are After-Market zippers.
Will NOT fit after-market top canvas.
Stainless Steel Snaps included but NOT installed in canvas (to allow perfect alignment on install), need Snap Tool.
Includes Mounting Track or Zipper and Snap-Stud-Screws.
100% Guarantee: We guarantee our mooring covers, bow covers, cockpit covers, bimini tops, camper tops, and other marine canvas enclosures
Will fit your boat to the specs provided,
Will match your existing GLBT canvas,
Will perform as described when installed properly,
Will completely satisfy you with the quality and construction.
You can count on all of the above or else the boat top or enclosure will be replaced or your money returned. Your boat is a large investment so be sure you protect it with the best marine canvas direct from the factory.
Warranty: This product is covered by the Manufacturer's Warranty.