Purchase Cockpit Cover Bimini Camper Cutouts (Factory OEM) part number [9ySR270DASESN1-x0xxx-f97] for 1998-1999 Sea Ray® 270 Sundancer Special Edition 270SE Sundancer Special Edition, 8-foot 6-inch beam (Trailerable), Sea Ray Hull Prod Number below HIN on Transom begins with 270DASE- (Not the wider 270SDA), NO Arch or Tower
Sea Ray, 270 Sundancer Special Edition, 1999, Cockpit Cover, Bimini Top in Boot, Camper Top in Boot, Starboard Rear.
Great Lakes Bow and Cockpit Cover, Adjustable Support Pole, Snaps.
Images (random) of Cockpit-Cover-Bimini-Camper-Cutouts-OEM-G0.5 (additional canvas pieces or covers may also be shown above, click images to enlarge)
Factory Snap-On COCKPIT-COVER with Cutouts (openings) for Bimini-Top AND Camper-Top Frames, Adjustable Support Pole(s) and reinforced Snap(s) or Grommet(s) inside Cover for Tip of Pole(s), OEM (Original Equipment Manufacturer) in Sunbrella® marine fabric, produced with the same high quality, original 1998-1999 digitized patterns approved by Sea Ray® for the 270 Sundancer Special Edition: 270SE Sundancer Special Edition, 8-foot 6-inch beam (Trailerable), Sea Ray Hull Prod Number below HIN on Transom begins with 270DASE- (Not the wider 270SDA), NO Arch or Tower:
Notes:
1998-1999 Sea Ray® 270 Sundancer Special Edition Model Specific Details: Check Hull Prod Number below HIN for 270SASExxx. Says 270 SUNDANCER SPECIAL EDITION on decals on sides of boat. NO Separate Dinette in the Cabin. Glass fore deck hatches. See http://www.clubsearay.com/index.php?threads/mid-90s-270-sundancer-thread.936/ . An angled Bimini Aft Curtain OR a 'stand-up' Camper Top with Side and Aft Curtains are offered at the rear. Sea Rays with 12-digit Hull Identification Number (HIN) beginning with SERA were made in Arizona for which we do NOT have OEM canvas patterns (this boat was built by Sea Ray in AZ and TN): our Tennessee Sea Ray® Bow Covers, Cockpit Covers and Carpet Runners we offer will fit Arizona boats, however the original Arizona top frame(s) were made by someone else, so our Tennessee Bimini, Sunshade and Camper replacement canvas will NOT fit Arizona frames, AND our Visor, Side or Aft Curtains will NOT zip properly to original Arizona top canvas, BUT ALL Arizona canvas AND frames can typically be replaced as a set, however we do NOT guarantee fit. The Cockpit Cover goes OVER the windshield and snaps at the base of the windshield in front. Sea Ray® originally offered the 1998-1999 270 Sundancer Special Edition in Linen Tweed Sunbrella® (the Tops were originally SeaMark® vinyl-lined Sunbrella®, but are now Sunbrella® to avoid mold issues) fabric.
Product Details: Snaps tightly over the Cockpit area and has Velcro-Lined Cutouts to go around the Bimini-Top AND Camper-Top frames (not included). Comes with one or two (depending on size) Adjustable Aluminum Support Pole(s) with Snap or Grommet (hole) through reinforced area in center of Cockpit-Cover. Cockpit-Cover has 30 to 80 standard 3/8" snaps, depending on the boat. Includes Male Snap-Stud-Screws. Factory Original-Equipment (OEM) cover made-to-order.
Sea Ray® Factory Original Equipment Manufacturer (OEM) Notes: Zippers on Sea Ray® canvas are size #8 (6 teeth/inch) up to 35 foot, #10 over 35 foot (5 teeth/inch). Cockpit Covers for open bridge boats (Sundancer, SunDeck, SunSport, SLX, Bowrider, Express Cruiser, Weekender) prior to 2008 cover the windshield, 2008 and newer attach to Top of windshield. Embroidered Sea Ray® logo on SOME (when offered by Sea Ray) Boot Covers was Tan (gold) until 2011, then Silver 2012 and newer. Sea Ray® installed the snaps in their boats, canvas and covers at their factory, so we cannot install the canvas snaps for you because we do not have locations (see Canvas/Snap Installation to learn about installing snaps). We can only sell canvas and covers direct for Sea Ray® boats over 2 years old. Sea Ray® OEM canvas/covers part numbers: [yySRmmm mm tar-xxxxx-fcc] where [yy] is the model year, [SR] is Sea Ray®, [mmm mm] is the boat model, [t] is the type of window or drive (S=Std-Windshield, W=optional-stainless-Windshield, I=I/O-sterndrive, O=Outboard), [a] is (A)rch or (N)o-arch, [r] is the revision, [xxxxx] identifies which canvas piece, [f] is the fabric (A=Sunbrella® acrylic, S=SeaMark®) and [cc] is the color code. Sea Ray® Hull Identification Number (HIN) = SERpssssmbyy , where [p] = mfg plant, [yy] = model-year.
Factory Original-Equipment-Manufacturer (OEM) patterned for the {1998,1999} Sea Ray® 270 Sundancer Special Edition: 270SE Sundancer Special Edition, 8-foot 6-inch beam (Trailerable), Sea Ray Hull Prod Number below HIN on Transom begins with 270DASE- (Not the wider 270SDA), NO Arch or Tower.
Only fits Factory-Original Windshield, Arch/Tower (if so equipped), Bimini-Top and Camper-Top setups.
Snaps included but NOT installed in canvas, so a Snap Installation Tool is required.
Cut-outs for Bimini-Top-Frame and Camper-Top-Frame are made per Factory-Original specifications.
100% Guarantee: We guarantee our mooring covers, bow covers, cockpit covers, bimini tops, camper tops, and other marine canvas enclosures
Will fit your boat to the specs provided,
Will match your existing GLBT canvas,
Will perform as described when installed properly,
Will completely satisfy you with the quality and construction.
You can count on all of the above or else the boat top or enclosure will be replaced or your money returned. Your boat is a large investment so be sure you protect it with the best marine canvas direct from the factory.
Warranty: This product is covered by the Manufacturer's Warranty.
Lead-Time (Estimated): We no longer sell this product.
Shipping Notes:
Signature required for delivery,
Can NOT ship to Post Office (PO) Box,
Can NOT change your address after order is placed,
Buyer is responsible for all Taxes, Duties and Tariffs imposed by local governments,
Use a US48 Based (in Florida, New Jersey or Oregon for example) Freight Forwarder to ship outside the USA or Canadian Provinces,
Check shipment for damage upon receipt and file claim with shipper.
International Shipments:
We do NOT ship Sea Ray Cockpit-Cover-Bimini-Camper-Cutouts-OEM-G0.5 Outside North America (continental United States 48 States (US48) and Canadian Provinces), Overseas: Use a US-based Freight Forwarder,
Please contact a Freight Forwarder (instructions) with an address in the US48 (Florida preferred for timeliness) to ship this for you,
Also note that the Freight Forwarders address must be added to your Credit Card to complete payment.
Not what you need? Try:
